Powermatic Model 29 Shaper

• 27-5/8" x 35-1/2" extra-thick cast iron table
• Spindle tilts 45¸ forward and 5 degrees backward for bevel shaping
• Three standard table inserts, smaller insert has a guide shoulder for copy work
• Entire hold-down assembly flips out of the way for spindle changes
• Two hold-downs and cutterhead shield are standard equipment

STANDARD EQUIPMENT

• Motor
• Work piece hold-downs (2)
• Accu-Fence
• Mitre gauge
• Three table inserts (2-7/16", 6-3/8" and oval) for tilting spindle
• Three spindles (3/4", 1" and 1-1/4")
• Collet and router bit adaptors ( 3/8" and 1/2")
• Cutterhead shield
• Dust collection port
• Reversing switch

Price $9381.00 + shipping

The new TS29 is ready to tackle any job. A new fence design includes dual digital readouts, micrometer adjustments and independently adjustable fence halves for fast, easy, and accurate set-ups.

The full guard includes two stock hold downs and a see through cover that flip up for quick tool changes. Dual dust collection ports, in the guard and under the table insure a clear work area and improved finish.

An extra large quill assembly with a full seven inch stroke has three oversize bearings and the ability to tilt, adding versatility and insuring long, trouble free performance. Powered by a big 71/2HP motor that drives the spindle forward and reverse with five speeds.

The massive sliding table is fully supported by six tapered precision bearings through a full four foot stroke. In addition, on board the table is a large miter head complete with stock hold down clamp and a 56-inch miter fence with flip stop.

The large table can easily accommodate a stock feeder for longer production runs; this machine is built to handle any job.

Price $13123.00 + shipping

Powermatic TS29 Tilt/Slide Shaper

• Motor HP/Voltage/Phase 71/2HP 230/460V 3PH
• Electric Controls 24V magnetic
• Spindle Sizes with Capacity Under Nut 11/4" dia. x 61/4", 1" dia. x 6", 3/4" dia. x 31/2", 1/4" and 1/2" collets
• Spindle Travel 7" vertical
• Spindle Speeds rpm 3,000/4,000/6,000/8,000/10,000
• Tilting Spindle 5 deg. back, 45 deg. forward
• Overall Table Size L x W 511/2" x 331/2"
• Maximum Diameter Cutter Below Table 9"
• Maximum Diameter Cutter Above Table 12"
• Fence Size (with Dual Digital Readouts) 46" x 5"
• Fence Travel (Major and Minor) 53/8" and 35/8"
• Slide Table Size 111/4" x 511/4"
• Table Travel 491/4"
• Table Inserts One tilting, one straight
• Dust Connect Diameter (2) 5"
• Minimum CFM Required 800
• Shipping Weight 1,280 lbs, net weight 1,100 lbs
• Overall Dimensions 51"L x 44"W x 53"H
• Tools Supplied Spindle wrenches, Spanner wrench, Set of open end wrenches, Set of allen wrenches, Grease gun, Tool box

FEATURES

• Sliding table with miter head, hold down and fence
• Fully adjustable fence with dual digital readout
• Large table with built-in slider with room for stock feeder
• 7-inch vertical spindle travel
• Spindle tilts neg. 5 to pos. 45 degrees
• Large diameter multiple table inserts
• Five spindle speeds in forward and reverse with lighted indicator

BENEFITS

• Can accommodate everything from multiple end cuts to tenons
• Fast and accurate set-up and repeatability
• Supports large work pieces; added safety option with feeder
• Allows user to stack tooling
• Increased versatility with tooling
• Accommodate virtually any size cutter
• The correct speed for any job