|
|
Figure 1
Bending Pipe and Conduit
Bends cold all sizes of standard pipe and Conduit up to 2" inside Diameter. Makes a smooth even bend without flattening the pipe or splitting the seam. Bends to any degree or to a continuous coil Bends to a10" radius on a 2" size,
down to a 2" radius on 1/4" size
|
|
 |
Figure 2
Bending on
the Hossfeld #2
Bending Eye Bolts, "S" shapes U shapes of round or square stock up to 5/8", cold. By using a wider bending dog and longer forming pin, flat stock up to 1-1/2" in width can be handled. With standard equipment Eyes and "U",s
can be bend with 1/2, 5/8", 3/4", 7/8" and 1" inside openings
|
|
 |
Figure 3
Hossfeld #2
Bends angles, Irregular shapes, Offsets of round or square stock up to 1-1/4" or of flat stock up to 4-1/2" x 1/2". Gauges are provided for accurately locating the point of bend and for gauging the degree of the angle desired
|
|
 |
Figure 4
Hossfeld #2
Bends "U" shapes of 1-1/4" round or square stock or of 4-1/2" flat stock cold. Self locking cam shaped dies for bending "U,s of 1-3/4", 2" and 2-1/4" inside spread are furnished with general purpose dies
|
|
 |
Figure 5
Bends sharp bends to a right angle or less on 4-1/2" x 1/4" flat stock cold. This feature of the bender is used where a real sharp corner bend is required, it can be used for making sharp offsets, stake pockets, sharp cornered
"U" clips
|
|
 |
Figure 6
Rings and continuous coils of any desired diameter can be formed. The forming ring may be a short piece of pipe of the right diameter or a #20B1 bushing can be purchased from our parts catalog. The stock is fed along a distance of 1" or
2" after each pull of the hand lever
|
|
 |
Figure 7
Sharp cornered "U" bolts are bent on the same feature of the bender as shown for bending ornamental iron. This feature is also used for bending short close hooks on the ends of rods. It will bend a hook with sharp inside corners and
having an inside spread of as close as 5/8" It has a capacity of 5/8" round or square stock or 3" x 1/4" flat stock cold
|
|
 |
Figure 8
This feature of the bender is used in making ornamental iron shapes and various other intricate bends. Bends a sharp corner and will handle work as small as the making of a staple or a small nail. This feature has a capacity of 3" x
1/4" flat stock or 5/8" round
|
|
 |
Figure 9
Attachment for bending Angle Iron with either the flange inward or Outward. Consist of a master die with which forming blocks of various radii can be used. These blocks work on a wedg principle so that when the bending pressure is applied the
horizontal flange of the stock is held in a vise like grip to prevent crimping or twisting
|
|
 |
Figure 10
Hossfeld #2
Forming blocks for bending radii of 5, 6, 7, 9, 12, 15, 18, 24, 30, and 36" are furnished with inbend and outbend attachments. Blocks for any radius up to 10' (minimum inbend 4", outbend 3") can be furnished if desired. Both inbend
and outbend attachments have a capacity of 2" x 2" x 3/16" cold or 2" x 2" x 3/8" hot
|
|
|
Figure 11
Bend edgeways with edgebend dies used with outbend master die, wrist pin and inner radius block. Size of inner radius block determines radius of bend. Capacity 3/8" x 1-3/4" cold. Bends flat edgeways from 4" inside radius and up to
any degree including 360 degrees circles. Same set up used for bending hand rail capping sideways
|
|
 |
Figure 12
Bending Notched Angle Iron
This feature of the bender is used for bending sharp bends on angle iron after the point of bend has been notched, Capacity 2-1/2" x 2-1/2" x 5/16" This special die will also form sharp "V" bends on flat stock.
|
|
 |
Figure 12-1
Bending larger diameter rings of Eyes
2-1/2" and larger Eyes or rings may be made using the #20B1 cast cam mounted over the #53B2 center pin
|
|
 |
Figure 13
Bending round or square eyes on flat stock
The bulldozer die is designed for making round or square bends on stock up to 3/16" thick and 4-1/2" wide The advantage of this die for sharp square bends, is that the stock can be easily removed by pulling a pin, thus round or square
eyes can be made. Also the die is ideal for making intricate bends on wire up to 1/4" diameter
|
|
 |
Figure 14
For cold bending 16 gauge thru 10 gauge OD tubing and schedule 40 pipe up to 180 degrees without the use of a mandrel or filler. Tube size available 3/8" to 2" pipe 1/4" to 2"
|
|
 |
Figure 14-1
Hossfeld #2 Bender
Large radius bends of coils on 3/8" thru 2" OD tube and 1/4" thru 2" schedule 40
|
|
 |
Figure 15
This rigid Conduit bending die is used mainly by electricians for quality production of 90 degrees ells. The capacity is 1/2" - 1-1/2" schedule 40 pipe
|
|
 |
Figure 16
Specially designed dies for re-bar sizes through 1" grade 40 make easy to bend fill-in mat and saddles as needed on the job. Mounts on bench or rugged steel pedestal
|
|
 |
Figure 17
Scroll bending dies form uniform single turn scrolls 2-1/2" 4" and 5" diameter and one and one half turn scrolls 6-1/2" and 8" diameter, Hand operated forms complete scrolls in seconds. Capacity 3/16" x 3/4"
|
|
 |
Figure 18, 19, 20
Bending Lambs tongue for bending hand rail capping up to 1/2" x 1-3/4" Volutes and edge bending
|
|
 |
Figure 21
Bends 1/2" to 1-1/4" size EMT on 90 degrees single pull dies. Smooth bends no wrinkles, no mandrels or fillers are needed
|
|
 |
Figure 22
Bends 1-1/2" to 2" sizes on feed along type die. Ideal for making large EMT standard radius, 90 degree and 180 degree return bends and offsets
|
|
 |
Figure 23
Smooth bends on square tubing |
|
 |
Figure 23-1
1/2", 3/4", and 1" square tubing, 16 gauge through 10 gauge wall, to 3", 4", 5" and 6" inside radius are available
|
|
|
Figure 23-2
Large radius bends from 8" inside radius and up, on Square tube up to 1-1/2"
|
